Shopping Cart

Your cart is empty.

Your cart is empty.

RED WOLF Remote Battery Terminal 3/8” M10 Stud, 250A Max DC 12V Battery Jumper Post Adapter Connector Relocation Heavy Duty for UTV ATV Automotive RV Truck Boat Trailer w/Insulating Cover

Free shipping on orders over $29.99

$18.99

$ 8 .99 $8.99

In Stock
  • Battery Remote Jump Start: Features a versatile remote post setup that can be mounted anywhere in any position, providing easy access to difficult-to-reach battery locations on equipment while serving as a terminal for other power needs, allowing convenient charging or jump-starting without accessing the engine bay
  • Heavy Duty Material: RED WOLF 3/8” M10 jump battery terminal construction is heavy and solid with quality brass materials, which provide exceptional stability, wear resistance, and corrosion protection for optimal conductivity
  • PVC Security Insulating Cover: Flame-retardant (VW-0 rated) protective cap for battery terminals; Designed to maximize coverage of exposed conductive surfaces, reducing accidental contact risks, preventing short circuits, and improving electrical safety
  • Convenient to Install: Battery terminal is compactly designed to be mounted on panels up to 0.3 inches thick through 1-1/4 inch holes; The 3/8-inch brass terminals on the other side can accommodate the largest battery cable lugs
  • Wide Application: 3/8 inch stud car charging jump post is an essential component for a wide range of vehicles and equipment; Ideal for Car RVs Yachts and Marines connecting battery to various equipment



Product Description

Remote Battery Terminal 3/8” M10 Stud

1464 x 600

Remote Battery Terminal 3/8” M10 Stud, 250A Max DC 12V Battery Jumper Post Adapter Connector Relocation Heavy Duty for UTV ATV Automotive RV Truck Boat Trailer w/Insulating Cover

1464 x 600

NOTE: MAX Continuous Current will DECREASE with Temperature & Humidity Effect

Details

300 x 225

M10 Stud Terminal

1.5

0.79" Thickness Copper Plate

Excellent conductivity

300 x 225

PA66 Nylon

Flame-retardant (VW-0 rated) protective cap for battery terminals

300 x 225

Remote Battery Terminal

Red - Positive

Black - Negative

Wide Application

1464 x 600

Features a versatile remote post setup that can be mounted anywhere in any position, providing easy access to difficult-to-reach battery locations on equipment while serving as a terminal for other power needs, allowing convenient charging or jump-starting without accessing the engine bay

1464 x 600

D. Lavren
Reviewed in the United States on July 9, 2025
This is a set of two remote battery terminals. The terminals are easily mounted in a single panel hole. The bottom of the terminals has an M10 threaded stud with washers and hex nut for ready connection to wiring connectors (not include). One terminal is colored red and the other is black for proper polarity connections. Each terminal has a tethered and removable rubber cap that protects the terminal from weathering, dirt and grit. The cap is easily removed to expose the copper connection terminal. These terminal assemblies are rated at 12v and 250A. These Terminals can be used in any 12V power system like solar, truck, RV or boats.Would recommend these to anyone.
Bob F
Reviewed in the United States on July 8, 2025
Talk about robust/beefy, these things are CHONKY! All that means is that I was very impressed when I put these in hand. I was half expecting typical low quality metals that felt hollow, but not the case for these.They are super thick, pretty heavy and can handle a massive amount of current. Way more than I needed, but my little DIY power bank is going to have some overly engineered posts and I'm not complaining!
pmoy
Reviewed in the United States on July 10, 2025
I’m using these as the main terminals on a DIY 14.4V/150AH battery made from LiFePO4 prismatic cells. The battery is for powering a trolling motor on a small boat. Installation of the terminals just requires drilling two holes and securing the terminals with a locknut. The instruction says to use a 32mm drill bit. The closest size bit I own was 1-1/4”. I had to enlarge the hole slightly using a round file after drilling. These terminals have a 3/8-16 stud on one end for connecting to the battery. I used three 8-gauge wires to connect from the BMS and battery to the terminals. Using three 8-gauge wires is probably overkill for the amperage the motor will be drawing, but I would rather err on the conservative side.Overall, I’m impressed by the quality of these terminals. They look nice and are well-made. They’re perfect for my application.
Recommended Products

$8.45

$ 3 .99 $3.99

4.3
Select Option