Your cart is empty.

PC-6011SD Clamp Power Analyzer Graphic Power Quality Analyzer for 1 Phase or Balanced 3 Phase System with Harmonic Analysis | Voltage Range 10 to 600 ACV | Current Range 5 to 2000 ACA

5.0 Write Review

Free shipping on orders over $29.99

$699.00

$ 99 .00 $99.00

In Stock

Qty.:

Energy ( KWh、KVAh、KVARh、PFh ) measurement.
Voltage measurement range: 10 to 600 ACV; Current measurement range: 5 to 2000 ACA.
Voltage and Current harmonic analysis ( 1-50th order ).

Peak-to-Peak voltage and current measurement.
Capture Transient events ( including Dip, Swell and Outage ) with programmable threshold ( % ).
Thermocouple Temp. sensor:Type K ( -100.0°C to 199.9°C/200°C to 1300°C),°C/°F.
Programmable PT ratio ( 1 to 1000 ).
Safety Standard : IEC 1010, CAT IV 600V.
Built-in clock and Calendar, real time data record with SD memory card , sampling time set from 2 to 7200 seconds. Just slot in the SD card into the computer, it can down load the all the measured value with the time information ( year, month, data, hour, minute, second ) to the Excel directly, then user can make the further data analysis by themselves.
Allow save the LCD screen picture to the photo BMP file, it is the useful tool for the user to make the further analysis.
Micro SD CARD 32 GB maximum supported capacity.
Powered by AA (UM-3) DC1.5V X 2 batteries ( Alkaline type ) or DC 9V adapter ( linear 110V/220V ).
Computer data output, can cooperate with optional USB Cable/USB-01, RS232 cable/UPCB-02 and Data Acquisition software, SW-U811-WIN.
Optional type K probe: TP-11.

Circuit	Custom single-chip microprocessor LSI circuit
Display	LCD Size: 3.2 X 2.4" (60 X 44.4 mm) / Dot Matrix backlit LCD (128 X 64 pixels)
Measurements	ACV, ACA, KW / KVA/ KVAR/ PF, KWH/KVAH/KVARH/PFH, Power factor, Phase angle, Frequency, Harmonics display, Temperature
Wire configurations	1 Phase, 3 Phase
Voltage ranges	10 ACV to 600 ACV (Auto Range)
Current ranges	5 ACA to 2000 ACA (Auto Range)
Safety standard	IEC1010 CAT IV 600 V
ACV input impedance	10 M ohms

Clamp frequency response	40 Hz to 1 KHz
Tested clamp	45 to 65 Hz
Over-load protection	ACV: 720 ACV RMS \| ACA: 2100 ACA with clamp probe
Over-range	* LCD display show " OL ". \| * The data save into the SD card will show " 9999 " or " 999 " (overleap the decimal point).
Data Hold	Freezes displayed reading
Datalogger	* Real time data logger, saved the data into SD memory card and down load the all the measured value with the time information ( year/month/data/ hour/minute/second ) down load to the Excel. \| * Sampling time for data logger : 2 seconds to 7200 seconds, the during of setting step are 2 seconds \| * Data error no. : ≦ 0.1% no. of total saved data typically.
Data Recording	Micro SD memory card
Sampling Time	Approx. 1 second

Data Output USB/RS232	* Computer interface \| * Connect the optional USB cable USB-01 will get the USB plug. \| * Connect the optional RS232 cable UPCB-02 will get the RS232 plug.
Operating Temperature	0 to 50°C ( 32 to 122°F ).
Operating Humidity	80% Relative Humidity max.
Power Supply	DC 1.5V, AA ( UM-3 ) Battery X 2 PCs (Alkaline or heavy-duty battery). \| AC to DC 9V power adapter ( LINEAR 110/220V )

Power Consumption	60 mA DC
Max. Conductor size	Clamp can accommodate up to 2.2" (57 mm) diameter
Dimensions	11.0 X 4.2 X 1.9" (280 X 106 X 47mm) \| Clamp Jaw: 3.5" (90 mm)
Accessories Included	Instruction manual....................... 1 PC 8 GB micro SD card...................... 1 PC Test Leads...................................1 set Alligator clips................................1 set AC to DC 9V adapter ( linear 110V/220V ).....................1 PC Carrying case...............................1 PC